High lift garage doors raise the tracks to free ceiling height for car lifts, storage and tall vehicles. How they work, requirements, costs and installation.
Contents
High lift garage doors use a vertical track that runs up the wall above the opening before turning toward the ceiling, so the open door parks much higher. That frees space for a car lift, overhead storage or a tall vehicle. A conversion commonly costs $800 to $2,000, and ceilings usually need to be 10 feet or more.
High lift garage doors are a popular change in garages with tall ceilings that standard track layouts waste.
Key Takeaways
A high lift system extends the vertical track above the opening and uses special cable drums, longer cables and re-sized springs.
The ceiling needs to be roughly the door height plus the lift amount plus about 18 inches.
Most high lift doors use a wall-mounted jackshaft opener, which also clears the ceiling.
A high lift garage door conversion commonly costs $800 to $2,000, plus a jackshaft opener if needed.
This is not a DIY job, because the springs must be recalculated and rewound for the new travel.
What Is a High Lift Garage Door System?
A high lift system extends the vertical track above the opening, then curves into a short horizontal track near the ceiling. Special high lift cable drums and longer cables let the springs balance the door through the extra travel.
The amount of "high lift" is the extra vertical track above a standard setup. A door with 3 feet of high lift climbs 3 feet up the wall before it turns, so the open door sits 3 feet closer to the ceiling than it would on standard track. Installers choose the lift amount based on the ceiling height and what you plan to put under the door.
Most high lift systems are built for sectional garage doors, because the hinged panels can follow the curve between the vertical and horizontal track. The door itself does not change, but the track, cable drums, cables, springs and usually the opener do. If you want a refresher on how those parts work together, see how garage doors work.
The Benefits of High Lift Garage Door Conversion
The main benefit of a high lift garage door conversion is usable space. A standard track leaves the open door hanging just above the opening, which blocks the upper part of the garage. So raising the track moves that dead zone up toward the ceiling.
Clears overhead space for a car lift.
Allows ceiling-height storage racks.
Lets more natural light from high windows reach the floor.
Keeps the door out of the way of tall vehicles and equipment.
There are also smaller benefits. The horizontal track is shorter, so less hardware runs down the middle of the ceiling and lights are easier to place. A wall-mounted jackshaft opener, which most high lift doors use, also frees the ceiling of the opener rail and motor. For homes with tall garages in newer California subdivisions, high lift garage doors can make a two-car garage feel noticeably larger.
Who Needs High Lift Garage Doors?
High lift garage doors are most common in garages where the ceiling sits well above the door and the owner has a specific use for the space overhead. Typical projects include:
Two-post or four-post car lifts in hobby garages and home workshops.
Overhead storage platforms for bins, holiday decorations and camping gear.
Tall vehicles such as lifted trucks, vans and small RVs that need clearance once inside.
Garages with high windows or skylights that a standard-lift door would shade.
Home gyms that need clear space for overhead lifts or pull-up rigs.
A good candidate garage usually has the following:
Ceilings well above the top of the door, often 10 feet or more.
Room on the side walls for vertical track and a wall-mounted opener.
A plan for the space: car lift, racks or a tall vehicle.
A high lift door also frees the upper walls and ceiling for overhead storage. With the horizontal track raised close to the ceiling, racks, deep shelving or a small loft can sit below it without blocking the door. Plan the track height around the storage depth you want, and leave clearance for the opener and springs, so the bins and the door never compete for the same space.
What Does a Garage Need for a High Lift Door?
The technical requirements for a high lift installation come down to ceiling height, side room, solid mounting surfaces and a correctly sized counterbalance system. An installer measures each one before quoting.
A high lift garage door conversion usually means new vertical and horizontal track, longer cables, larger cable drums, re-sized springs and often a jackshaft opener. It is a job for an experienced installer because the spring setup changes completely.
As a rule of thumb, the ceiling needs to be at least the door height plus the lift amount plus about 18 inches for the curve and springs.
Headroom: the clear height from the top of the opening to the lowest ceiling obstruction, such as beams, ducts or lights.
Side room: space on each side of the opening for the taller vertical track and, on one side, a jackshaft opener.
Backroom: depth from the door to the back wall, which matters less with high lift because the horizontal track is shorter.
Mounting surface: solid framing above the opening and along the walls to carry the springs and track brackets.
In California, installers also pay attention to how the vertical track and springs are anchored. Solid fastening into framing, rather than drywall alone, helps the system ride out earthquake shaking. A new opener added as part of the job needs a battery backup under California law.
Measure headroom before you settle on high lift, because it decides which system fits. A high lift door needs extra clearance above the opening so the vertical track can run up the wall. In contrast, a low headroom track kit solves the opposite problem: it lets a sectional door work in a garage with very little space above the door. If your headroom is tight, high lift is usually off the table.
How Do High Lift, Standard Lift and Vertical Lift Differ?
The difference between the three systems is where the open door ends up. A standard lift parks the door just above the opening, a high lift parks it near the ceiling, and a vertical lift sends it straight up the wall with no horizontal track at all.
A full vertical lift goes one step further: the door travels straight up the wall with no horizontal track at all. As a result, it needs a ceiling roughly twice the door height.
Factor
Standard lift
High lift
Where the open door sits
Just above the opening
Near the ceiling
Ceiling height needed
Door height plus about a foot
Significantly more; depends on lift amount
Opener
Standard rail opener
Usually a jackshaft (wall-mounted) opener
Usable overhead space
Limited
Much more
For most homes with an ordinary 8 to 9 foot ceiling, standard lift is the only practical choice. High lift, however, makes sense from roughly 10 feet up. Full vertical lift is mostly used in commercial buildings and very tall residential garages, and it requires the most specialized springs and hardware. Our guide to garage door tracks covers the track types in more detail.
How Much Does a High Lift Garage Door Conversion Cost?
A high lift conversion typically costs $800 to $2,000 for the hardware and labor, before any opener upgrade. The final price depends on a few variables:
A conversion on an existing door commonly costs $800 to $2,000 including track, drums, cables and springs, plus the cost of a jackshaft opener if needed. New high lift garage doors are priced like the door plus the special hardware.
Cost factor
Why it changes the price
Amount of lift
More lift means longer track, longer cables and larger drums.
Door size and weight
Heavier doors such as wood or double-wide steel need larger springs.
Spring system
Most conversions use new torsion springs sized for the extra travel.
Opener
A jackshaft opener usually replaces a ceiling rail opener.
Garage condition
Added framing, moving lights or relocating ducts adds labor.
Ask for an upfront quote that lists the track, drums, cables, springs and opener separately so you can compare bids.
Professional Installation vs. DIY Considerations
This is not a DIY project. That is because the springs must be recalculated and rewound for the new travel, and errors leave a heavy door unbalanced. Hire an installer experienced with high lift conversions.
A professional installer handles the parts of the job that carry real risk: removing the old springs safely, calculating the new spring size for the door weight and travel, setting cable tension on the high lift drums and balancing the door. Springs and cables store a large amount of energy, so a mistake can cause serious injury or drop the door.
What homeowners can do, however, is plan. Clear the walls and ceiling near the door, decide exactly where a lift or racks will go, and note any lights or ducts in the way. After installation, keep up basic care such as lubricating the moving parts and watching for frayed cables. If anything about the springs looks wrong, read about garage door spring replacement and call a technician.
Frequently Asked Questions About High Lift Garage Doors
These are the questions California homeowners ask most often before converting to a high lift garage door.
How much ceiling height do I need for a high lift garage door?
Roughly the door height plus the amount of lift plus about 18 inches for the curve and springs. For example, a 7 foot door with 3 feet of high lift needs about 11.5 feet of clear ceiling. High lift generally makes sense from roughly 10 feet up, while 8 to 9 foot ceilings suit standard lift.
Does a high lift conversion affect my garage door opener?
Usually yes. A standard rail opener cannot reach the extra travel, so a jackshaft opener mounted beside the door is the common choice. It also frees the ceiling of the opener rail and motor. In California, a new opener added as part of the job must also have a battery backup.
Can I convert my garage door to high lift myself?
It is not recommended. The springs must be removed, re-sized and tensioned for the new travel, and cable tension must be set on the high lift drums. Springs and cables are under high tension and can cause serious injury if handled incorrectly. Hire an installer experienced with high lift conversions instead.
Does a high lift garage door work with a torsion spring system?
Yes. Most high lift garage doors use torsion springs mounted above the opening, paired with special high lift cable drums. Extension spring systems are generally not suited to high lift track because of the extra vertical distance. A technician sizes the new springs for the door weight and travel.
Can any garage door be converted to high lift?
Not every garage qualifies. Most high lift systems are built for sectional doors, because the hinged panels can follow the curve between the tracks. The garage also needs a tall ceiling, often 10 feet or more, room on the side walls for taller track and a jackshaft opener, and solid framing for springs and brackets.