Garage door hinges let your door bend around the track curve. Anatomy, the numbering system, types, maintenance, replacement and upgrades.
Contents
Garage door hinges join the sections of a sectional door and carry the rollers. Each hinge is numbered so that the rollers sit at the right distance from the track as the door curves. When hinges wear or crack, they cause noise, misalignment and eventually a bent door.
This guide explains how these hinges work, what the numbers stamped on them mean, which types exist, how to keep them in good shape and when replacement is a safe homeowner job versus one for a technician.
Key Takeaways
Garage door hinges join the sections of a sectional door, carry the rollers and let the door bend around the track curve.
The hinge number shows how far the roller tube sits from the door face, starting with #1 between the bottom and second sections.
Most residential hinges are galvanized steel in 14 or 18 gauge, and a lower gauge number means thicker steel.
Lubricate the pivots, tighten fasteners and check for cracks every six months.
Homeowners can usually replace upper hinges one at a time, but the bottom hinge and bottom bracket carry spring tension and are a technician's job.
What Do Garage Door Hinges Do?
Garage door hinges are the pivoting brackets that connect each section of a sectional door and let the door bend as it rolls from the wall to the ceiling. Without them, a multi-panel door could not follow the curve of the track.
Hinges let the sections fold around the curved part of the track while holding them tightly together when the door is closed. They also position the rollers, so a bent hinge can make the whole door run crooked.
Hinges also take a share of the load every time the door moves. A typical two-car door cycles a few times a day, so each hinge flexes more than a thousand times a year. When one loosens or cracks, the sections can separate slightly, rub against each other and push the rollers out of line, which strains the garage door tracks, the rollers and the opener.
In California, two local factors add wear. Inland heat makes steel expand and contract every day, which slowly loosens fasteners, and coastal salt air speeds up rust on hinges that lose their galvanized coating.
Anatomy of a Garage Door Hinge
A garage door hinge is a simple part, but each piece has a job. Knowing the parts makes it easier to spot wear and to order the right replacement.
Basic Components
A hinge has two leaves joined by a pin, plus a roller tube or sleeve that holds the roller stem. Leaves are bolted to the stiles of adjacent sections.
The leaves are the flat plates that bolt to the door. On most steel doors they attach with self-tapping screws or carriage bolts through the end stiles and center stiles. The pin lets the leaves pivot, and the roller tube is set at a specific height, which is what the hinge number describes. Center hinges in the middle of the door have no roller tube at all.
Material Composition
Most residential hinges are galvanized steel in 14 or 18 gauge, where a lower number means thicker steel. Heavy doors and high-use doors benefit from thicker or double hinges.
Galvanizing protects the steel from rust, which matters in humid coastal areas from San Diego to the Bay Area. Once the coating wears through at the pivot, rust can seize the pin and make the hinge crack. Heavier doors, such as insulated, wood or overlay doors, often call for a heavier gauge than a basic single-layer steel door.
What Do the Numbers on Garage Door Hinges Mean?
The garage door hinge numbering system tells you how far the roller tube sits from the door face. Each number moves the roller slightly farther out, so the door is pulled tight against the weatherstripping when closed while the upper sections stay clear of the jamb as the door rises.
Always replace a hinge with the same number so the door keeps its alignment.
Hinge number
Typical position
#1
Between the bottom section and the second section
#2
Between the second and third sections
#3
Between the third and fourth sections
#4 and up
Higher sections on taller doors
The number is usually stamped on the hinge leaf. If it has worn off, compare the hinge with others at the same height on the opposite side of the door, since matching positions use the same number. Using the wrong number can make the door bind, rub the frame or leave a gap at the top that lets in light, dust and drafts.
Types of Garage Door Hinges
Standard residential hinges (#1 to #5).
Double end hinges for wide or heavy doors.
Heavy-duty 11 and 14 gauge hinges for commercial use.
Center hinges that join sections without a roller.
Double end hinges carry two rollers or a long-stem roller and spread the load on wide two-car doors. Heavy-duty hinges are thicker and resist cracking around the screw holes. If you are not sure which type your door uses, check the manufacturer label inside the door or compare the hinge with the options listed on our garage door parts guide.
The types of garage door hinges fall into three main groups. Standard numbered residential hinges suit most single and double doors. Heavy-duty hinges use thicker-gauge steel for wide, tall or insulated doors that weigh more. Double hinges spread the load on wide or heavy doors, usually on the end stiles. The right choice depends on the door's size and weight and on where the section sits in the door.
Maintaining Your Garage Door Hinges
Hinge maintenance takes a few minutes every six months: lubricate the pivots, tighten the fasteners and inspect for cracks. This simple routine prevents most hinge failures.
Lubricate the pivot points every six months, tighten loose bolts with the door closed, and look for cracks around screw holes.
Use a garage door lubricant or light silicone spray on the pin and the roller tube, then wipe off any excess so it does not collect dust. Our guide on how to lubricate a garage door covers which parts need lubricant and which should stay dry. Watch for these warning signs when you inspect:
Cracks around the hinge or screw holes.
Squeaking at one spot as the door moves.
Sections that do not line up or rub together.
A roller that sits crooked in the track.
A squeak that follows the door as it moves often points to a dry hinge pin. If the noise continues after lubrication, see our guide to fixing a noisy garage door for other likely causes.
When Should You Replace Garage Door Hinges?
Replace garage door hinges when they are cracked, bent, badly rusted or will no longer hold their screws. A cracked hinge rarely stays a small problem, because the load shifts to the neighboring hinges and they start to fail too.
Hinges on the bottom section are attached near the cable bracket, which is under spring tension. Those should be left to a technician. Upper hinges can usually be replaced one at a time with the door fully closed and the opener unplugged.
Close the door fully and unplug the opener.
Note the hinge number and position.
Remove the screws from one hinge only, keeping the sections supported.
Fit the new hinge with the same number, sliding the roller stem into the roller tube.
Tighten the screws snugly without stripping the steel.
Run the door by hand, then with the opener, and listen for rubbing.
If screw holes are stripped, the door has already split, or the bottom hinge is involved, call a technician. Those repairs connect to the torsion springs and cables, which hold enough tension to cause serious injury.
Most homeowners can replace garage door hinges on the upper sections of the door. Close the door fully, unplug the opener and swap one hinge at a time so the sections stay held together and the rollers stay in the track. Match the number stamped on the old hinge before you buy. Leave the bottom hinge and the bottom bracket to a technician, because they connect to the lift cables and carry spring tension.
Garage Door Hinge Upgrades: When and Why
Upgrade to heavy-duty hinges if hinges keep cracking, if you add insulation or overlays that make the door heavier, or if the door cycles many times a day.
Among the types of garage door hinges, an upgrade usually means a heavier gauge or double hinges on the end stiles. It costs little in parts and can stop a cycle of repeated cracks. Have a technician check door balance at the same time, because a door that is heavier than the springs are set for will keep stressing new hinges.
Common Questions About Garage Door Hinges
Why are my garage door hinges cracking?
Usually from an unbalanced door, heavy wear or an opener pushing too hard. Inland heat that loosens fasteners and coastal salt air that rusts the pivot add to the wear. A cracked hinge also shifts load to its neighbors, so they start to fail too. Have the door's balance checked when replacing them, because a heavy door keeps stressing new hinges.
How often should hinges be lubricated?
Every six months, at the pivot point. Use a garage door lubricant or light silicone spray on the hinge pin and the roller tube, then wipe off the excess so it does not collect dust. At the same time, tighten loose bolts with the door closed and look for cracks around the screw holes.
Can I replace garage door hinges myself?
You can usually replace upper hinges one at a time with the door closed and the opener unplugged. Leave the bottom hinges and anything near the bottom brackets to a technician, because they connect to the lift cables and springs, which are under high tension. If the door has split sections or stripped holes, a professional repair is safer.
How much do garage door hinges cost?
Standard residential hinges are inexpensive parts, and heavy-duty versions cost somewhat more. The larger cost comes when a cracked hinge has damaged a section or bent a track. Ask for a written quote before work; worn hinges are often replaced during a tune-up, so you pay for one visit instead of several.
What gauge garage door hinges do I need?
Most residential garage door hinges are galvanized steel in 14 or 18 gauge, and a lower number means thicker steel. Heavier doors, such as insulated, wood or overlay doors, often call for a heavier gauge than a basic steel door. Heavy-duty 11 and 14 gauge hinges are also used on commercial and high-use doors.
Why does my garage door squeak at the hinges?
A squeak that follows the door as it moves often points to a dry hinge pin. First, lubricate the pin and roller tube with a garage door lubricant or light silicone spray. If the noise continues, look for cracks, loose fasteners or sections that rub together, since those signs mean a hinge may need replacing.