
Contents
Garage door spring replacement means a trained technician removes worn or broken springs and installs new ones sized to the door's weight. It is the most common garage door service. A pair of torsion springs typically costs $200 to $450 installed, the job takes one to two hours, and it is never a DIY job.
Springs wear out with every cycle, so eventually every door needs new ones, while garage door spring repair covers smaller fixes such as tension adjustment.
Key Takeaways
A broken spring cannot be repaired; it must be replaced, usually together with its partner.
Garage door spring replacement cost for a pair of torsion springs is typically $200 to $450 installed.
Warning signs include a loud bang, a visible gap in the coil and a door that suddenly feels very heavy.
Standard springs are rated about 10,000 cycles, roughly 7 to 10 years, while high-cycle springs are rated 20,000 to 50,000 cycles.
Torsion springs store enough energy to cause serious injury, so homeowners should never replace garage door springs themselves.
Can a Broken Garage Door Spring Be Repaired?
A broken spring cannot be repaired; it must be replaced. Garage door spring repair usually means adjusting tension, lubricating or replacing related parts such as cables and bearings.
In practice, most service calls fall into one of two groups. If the door is slightly out of balance but the springs are intact, a technician may handle it as garage door spring repair: adjusting tension, lubricating the springs and replacing worn rollers or bearings. If a spring is broken, stretched, rusted through or past its cycle rating, the only safe fix is garage door spring replacement.
| Situation | Typical service |
|---|---|
| Door drifts up or down slightly | Tension adjustment and balance check |
| Springs squeak but look sound | Lubrication and inspection |
| Visible gap in a coil | Replace the springs |
| Door very heavy or opener strains | Inspect, usually replace the springs |
| Frayed or slack cables | Replace cables, check springs |
How Do You Know a Garage Door Spring Is Broken?
The clearest signs are a sudden loud bang, a split in the spring coil and a door that suddenly feels much heavier. Springs rarely fail without some warning, so these signs are worth checking for at least twice a year.
A loud bang from the garage.
A visible gap in the spring coil.
The door is very heavy or stops after a few inches.
Slack cables.
Other clues include a door that rises unevenly, closes too fast in the last foot of travel, or makes creaking and popping sounds as it moves. On extension spring doors, a spring that looks longer than its partner with the door open has lost strength. Our guide to 7 signs your garage door springs need repair walks through each warning sign in detail.
If you suspect a broken spring, stop using the opener and unplug it so nobody tries to run the door. Keep the door closed, keep children and pets clear of it, and do not try to lift it by hand, since the full weight is no longer supported. Then call a technician. If your car is trapped inside, ask about emergency service: some independent providers offer same-day or after-hours repairs.
Torsion vs Extension Springs – Which One Do You Have?
Look above the door: one or two springs on a shaft above the opening are torsion springs. Springs running along the horizontal tracks are extension springs.
The type matters because it changes the parts, the price and the replacement method. For example, torsion systems use a shaft, drums and winding cones. Extension systems, however, use pulleys, cables and safety cables that run through the center of each spring.
Torsion springs: smoother lift, longer-life options, and the spring stays on the shaft when it breaks. Learn more about garage door torsion springs.
Extension springs: common on older and lighter doors, lower upfront cost, and each spring needs a safety cable. See our guide to garage door extension springs.
Can I Replace Garage Door Springs Myself?
It is not recommended. Torsion springs store enough energy to cause serious injury, and winding requires proper winding bars and exact turn counts.
The risk is greatest during removal and winding, when the spring is fully loaded and your hands are close to it. A slipped winding bar or a spring that fails mid-adjustment can cause serious hand, arm and head injuries. Extension springs are less dangerous but still under tension, and a missing safety cable turns a broken spring into a projectile.
Homeowners should not replace garage door springs themselves, but they can safely do the visual checks, keep the springs lubricated and test the door's balance. Leave removal, winding, cable work and drum work to a trained technician.
For most homeowners, the answer is to leave it to a pro. To replace garage door springs safely, you need to release stored tension, use special winding tools, and choose springs sized correctly for the door's weight and height. A mistake at any of those steps can let the door drop suddenly or let a spring release its energy at your hands. In short, the money saved rarely justifies that risk.
What Happens During Garage Door Spring Replacement?
A professional spring replacement visit usually takes about one to two hours. The technician secures the door, replaces the springs, inspects related parts and finishes by balancing the door and testing the opener's safety features.
Securing the door.
Unwinding and removing old springs.
Measuring the door weight and spring dimensions.
Installing new springs, usually both.
Inspecting cables, drums and bearings.
Balancing the door and testing the opener.
Most technicians replace both springs on a two-spring door, since the second spring has the same wear. They also look at the lift cables, drums, bearings and rollers, because those parts wear at a similar rate and are cheaper to replace while the door is already secured.
Choosing the Right Springs for Your Garage Door
The right springs match your door's weight, height and daily use. The technician measures wire size, inside diameter and length, then recommends a cycle rating that suits how often your household uses the door.
| Option | Benefit |
|---|---|
| Standard 10,000 cycle | Lowest upfront cost |
| High-cycle (20,000+) | Longer life for heavily used doors |
| Extension to torsion conversion | Smoother, safer operation |
| Oil-tempered or coated springs | Better corrosion resistance |
If the garage is your main entrance, a high-cycle spring usually pays off because it delays the next replacement. Near the coast, also ask about coated springs that resist rust from salt air.
How Much Does Garage Door Spring Replacement Cost?
The typical garage door spring replacement cost for a pair of torsion springs is about $200 to $450 installed, with high-cycle springs and heavy doors at the upper end or above. The final price depends on the factors below.
Torsion or extension system.
One or two springs.
Standard or high-cycle springs.
Door weight and size.
Cables, bearings or drums replaced at the same time.
After-hours service.
Ask for an upfront quote before work begins. It should list the spring type and cycle rating and any cables, bearings or rollers being replaced. If a spring breaks outside business hours, some providers offer emergency garage door repair, which may carry an after-hours charge.
In short, the garage door spring replacement cost moves with four things: whether the door uses torsion or extension springs, how many springs it has, whether you choose standard or high-cycle springs, and whether cables or rollers are replaced in the same visit. Doing worn cables or rollers at the same time adds parts, but usually saves a second service call later.
How Long Do Garage Door Springs Last?
Standard springs are rated about 10,000 cycles, roughly 7 to 10 years for typical use. High-cycle springs rated 20,000 to 50,000 cycles last much longer.
To estimate your own spring's life, divide the cycle rating by the number of times your household opens and closes the door each year. A family that runs the door four times a day uses about 1,460 cycles a year, so a 10,000-cycle spring lasts roughly 7 years. Rust, a door that is out of balance and a lack of lubrication all shorten that.
Frequently Asked Questions About Garage Door Spring Replacement
Should both garage door springs be replaced at the same time?
Yes. They have the same wear, and the second is usually close to failing. Replacing both in one visit keeps the door balanced and saves a second service call. Most technicians also check the lift cables, drums and bearings at the same time, because those parts wear at a similar rate.
Can I open my garage door if the spring is broken?
Avoid it. The remaining spring cannot safely carry the weight, and the door may fall. Unplug the opener so nobody runs it, since repeated attempts can strip the opener's gears. Keep the door closed and keep children and pets clear. If your car is trapped, ask a provider about emergency service.
How long does a garage door spring replacement take?
Most spring replacements take about one to two hours. A conversion from extension to torsion springs usually takes longer because more hardware is replaced. During the visit, the technician secures the door, replaces the springs, inspects cables, drums and bearings, then balances the door and tests the opener's safety features.
Should I upgrade to high-cycle springs?
High-cycle springs make sense if the garage is your main entrance or the door runs many times a day. They are rated for 20,000 to 50,000 cycles instead of the standard 10,000, so they cost more up front but can save you a second replacement visit. For a rarely used door, standard springs are usually enough.
What does a broken garage door spring sound like?
A broken spring usually makes a sudden loud bang from the garage. Afterwards the door feels much heavier, may stop after a few inches and often shows a visible gap in the spring coil. If you hear a bang and the door will not open, unplug the opener before trying again, because repeated attempts can strip its gears.
Is it worth converting extension springs to torsion springs?
It can be. An extension to torsion conversion gives smoother, safer operation, and torsion springs come in longer-life options and stay on the shaft when they break. Extension springs cost less up front, but each one needs a safety cable. A conversion usually takes longer than a standard spring replacement because more hardware is replaced.
Sources & References
- DASMA – Technical Data Sheet #190: Factors Affecting Spring Cycle Life. Why a spring's real life differs from its cycle rating (checked November 2026)
- DASMA – Technical Data Sheet #171: Official Color Codes for Torsion and Extension Springs. Identifying spring wire size by color code (checked November 2026)






