
Contents
Garage door opener repair fixes the motor unit, drive parts, safety sensors or controls that move your garage door. Most opener repairs cost about $100 to $350 and take 1 to 2 hours. A new opener, installed, typically costs $350 to $750. Before you book a repair, check the door itself, because a broken spring often looks like an opener problem.
CA-GarageDoor connects California homeowners with independent garage door providers. The provider diagnoses the opener, quotes the repair and does the work. For problems with the door itself, see our garage door repair guide. To compare drive types and features, see our guide to garage door openers.
Key Takeaways
Most garage door opener repairs cost $100 to $350. A new circuit board can cost up to $400.
Check the door's balance first. A heavy or uneven door points to the springs, not the opener.
You can safely check the power, the lock or vacation mode, the safety sensors and the remote batteries yourself.
Openers usually last 10 to 15 years. On an older opener, compare the repair quote with $350 to $750 for a new installed opener.
Repairing your existing opener does not trigger California's battery backup law. A new opener or a new garage door does.
Is It the Opener or the Door?
Many opener problems start with the door, not the opener. The springs lift the door's weight, and the opener only guides a balanced door. So a broken spring can make the opener strain, hum or stop. Chamberlain lists broken springs as one cause of an opener that hums while the door does not move.
To check, close the door and pull the emergency release to disconnect the opener. Lift the door by hand to about halfway and let go. A balanced door stays roughly in place. If the door is very heavy, or drops or rises on its own, the springs need attention before the opener. See broken garage door spring repair. If a spring is visibly broken or the door is too heavy to lift, leave the door closed and call a professional technician.
Garage Door Opener Not Working? Common Problems and Causes
Most garage door opener problems show up as one of six symptoms. Match what you see and hear to the likely cause below. Then decide whether it is a quick check you can do yourself or a job for a provider.
Opener Runs but the Door Doesn't Move
When the opener runs but the door doesn't move, the most common reason is a disconnected trolley, also called the carriage. Pulling the red emergency release cord disconnects the door from the opener. Genie and Chamberlain both say to reconnect the trolley before looking further.
If the trolley is engaged and the door still does not move, the cause is usually in the drive. Common causes are a broken chain or belt, a chain or belt off its sprocket, or a stripped gear or rack. On screw drive models, a worn coupler is another cause. A provider can replace these drive parts.
Opener Hums or Clicks but Won't Start
When an opener hums briefly but won't start, it usually means the opener cannot move the door. Chamberlain lists an activated door lock, a trolley stuck against the stop bolt and broken springs as causes. On some models, Chamberlain also lists a swollen or leaking capacitor, a damaged motor or a damaged receiver logic board.
Capacitor, motor and board work happens inside the motor unit. Disconnect all power and leave that work to a professional technician.
Door Stops or Reverses Partway
A garage door that stops or reverses on the way down is usually reacting to its safety sensors, its travel limits or its force setting. The door may also be binding in the tracks. On Genie openers, a flashing light on the safety sensor means the sensor needs attention. The light should be on and steady. See why a garage door reverses before closing, how to align garage door sensors and how to adjust force settings.
Remote or Keypad Doesn't Work
When the wall button works but a remote doesn't, replace the remote's battery and reprogram the remote to the opener. Genie notes that when all remotes and wireless devices stop working at the same time, the circuit board may need to be replaced. Our guides cover garage door remotes and keypads and how to reset a garage door opener.
Lights Blinking or Error Codes
Blinking lights on many garage door openers are an error code: the opener flashes its lights in a pattern that points to the sensors, the travel limits or the motor. Count the flashes, then look up the pattern in your manual or in our guide to garage door opener error codes.
Opener Is Loud or Grinding
Chain drive openers are the loudest type of opener, and a loose chain, worn gear or dry rail makes them louder. Grinding from the motor unit can point to worn drive gears. See how to fix a loose garage door chain and how to fix a noisy garage door.
What You Can Safely Check Before Calling
Before you call, you can safely do a few free checks that fix many opener problems:
Plug a lamp into the opener's outlet. If the lamp doesn't work, check the breaker or GFCI outlet.
Turn off the lock or vacation mode on the wall control.
If the emergency release was pulled, make sure the trolley is reconnected.
Clean the safety sensor lenses and check that both sensor lights are steady.
Replace the remote's battery and reprogram the remote.
Reset the opener by following the steps in your manual.
Disconnect all power, including a battery backup, before you open the motor cover or touch any wiring. Chamberlain gives this warning before any service. Leave springs, cables and anything inside the motor unit to a professional technician.
What a Provider Checks During an Opener Repair Visit
During an opener repair visit, a provider usually starts by checking the whole door, not just the opener. That includes the door's balance and springs, the safety reversal and sensors, and the drive: chain, belt or screw, gears and trolley. The provider also checks the travel limits and force settings, any error codes and, on newer openers, the battery backup.
DASMA's checklist for home inspectors and consumers also checks the door's balance and springs along with the opener's safety reversal and photo-eye sensors. Most opener repairs take 1 to 2 hours. Ask for a written quote that lists parts and labor before you approve the work.
How Much Does Garage Door Opener Repair Cost?
Most garage door opener repairs cost about $100 to $350 for parts and labor. A service call or diagnostic fee of $50 to $75 is common, and many providers waive that fee when you approve the repair. Night, weekend and holiday visits can add $100 to $300.
Typical garage door opener repair costs in California
| Repair | Typical cost |
|---|---|
| Service call or diagnosis | $50 to $75 |
| Safety sensor alignment or replacement | $100 to $250 |
| Remote programming by a provider | $115 to $150 (a replacement remote costs about $15 to $50) |
| Chain repair or replacement | $100 to $200 |
| Motor repair or replacement | $100 to $250 |
| Circuit (logic) board replacement | $150 to $400 |
| New opener, installed | $350 to $750 |
Your final price depends on the part, the opener's brand and age, whether parts are still available and whether the visit is after hours.
Repair or Replace Your Garage Door Opener?
Repairing a garage door opener usually makes sense when the opener is less than about 10 years old and one part has failed, such as a sensor, a remote, a gear or a circuit board. Consider replacing the opener when it is 10 to 15 years old or older, or when parts are no longer available for the model. Replacement is also worth considering when the repair quote approaches the $350 to $750 cost of a new installed opener.
See our garage door opener installation cost guide and our comparison of the best garage door openers.
California adds one rule. Repairing an opener you already have does not trigger the state's battery backup law. If you replace the opener, the new one must have a battery backup. A new garage door also must not be connected to an existing opener without one. See California's garage door opener battery backup law.
Opener Repair by Brand: LiftMaster, Chamberlain, Genie and Craftsman
The opener problems above apply to LiftMaster, Chamberlain, Genie and Craftsman openers alike. Error codes, reset buttons and remote programming steps differ by brand and model. Check your model number on the motor unit, then see our guides to LiftMaster, Chamberlain, Genie and Craftsman openers.
Find Garage Door Opener Repair Near You
To find garage door opener repair near you, call (213) 221-2882 or send a service request. A provider that serves your area contacts you to arrange a visit and a quote. CA-GarageDoor connects homeowners across California with independent garage door providers.
Southern California: Los Angeles, Long Beach and San Diego.
Bay Area: San Francisco, Oakland and San Jose.
Central Valley: Sacramento and Fresno.
Elsewhere: see all California service areas.
Frequently Asked Questions About Garage Door Opener Repair
How long does a garage door opener last?
Most garage door openers last 10 to 15 years. Heavy daily use and an out-of-balance door shorten that lifespan, because both make the motor and drive work harder.
Can a stripped opener gear be replaced?
Yes. A stripped opener gear can usually be replaced without replacing the whole opener, as long as parts are still available for the model. The same goes for other worn drive parts such as a sprocket, rack or coupler. On an older opener, compare the repair quote with the cost of a new one.
Does a repaired opener need a battery backup in California?
No. Repairing the opener you already have does not require adding a battery backup in California. The state's battery backup law applies to openers sold or installed since July 1, 2019, and to new garage doors connected to an opener.
Why does my opener work from the wall button but not the remote?
The remote's battery is the most common cause when an opener works from the wall button but not the remote. The next most common cause is a remote that has lost its programming. Replace the battery, then reprogram the remote. If every remote and wireless device stopped at the same time, the opener's circuit board may need to be replaced.
Is it worth repairing an old garage door opener?
It depends on the repair and the opener's age. A simple fix such as a sensor or remote is worth doing on any working opener. For a motor or circuit board repair on an opener that is 10 to 15 years old, a new opener at $350 to $750 installed is often the better value.
Sources & References
- Chamberlain Group – Why does my garage door opener hum but the door does not move. Causes of a humming opener by drive type: door lock, trolley on the stop bolt, broken springs, capacitor, motor, logic board; disconnect all power before service (checked November 2026)
- Genie – Genie Garage Door Opener Troubleshooting. Disengaged carriage after the emergency release, sensor light, remotes and circuit board, power checks (checked November 2026)
- DASMA – Technical Data Sheet #167: Residential Sectional Garage Door and Electric Operator Checklist for Home Inspectors and Consumers. Checks door balance, springs, the opener's safety reversal and photo eyes; repairs and adjustments by a trained door systems technician (checked November 2026)
- This Old House – Garage Door Repair Cost (2026 Pricing). Opener repair ranges, service call fees, belt-drive opener lifespan (checked November 2026)
- Fixr – Garage Door Repair Cost. Opener, motor, circuit board, sensor, remote and chain repair costs; after-hours surcharge; opener lifespan (page updated January 2025) (checked November 2026)
- California Legislative Information – Health and Safety Code section 19892. Battery backup requirement for openers sold or installed in California (checked November 2026)








