
How to align garage door sensors step by step: preparation, indicator lights, brackets, height, horizontal alignment, testing and troubleshooting.

To align garage door sensors, unplug the opener, clean both lenses, loosen the brackets and aim the two sensors at each other at the same height, no more than 6 inches above the floor. When the receiver light glows steady, tighten the brackets and test that the door reverses when an object breaks the beam.
All you need is a screwdriver and possibly a string or level.
Misaligned sensors are the classic cause of a door that starts down, then reverses while the opener light blinks. This guide shows you how to align garage door sensors in five steps, how to fix stubborn problems and when to call a technician. For background on how the system works, see our main guide to garage door sensors.
A door that starts down, then reverses while the opener light blinks usually has misaligned sensors.
The sender's light stays on, while the receiver's light is steady only when it sees the beam.
Set both sensors at the same height, about 6 inches up, and check the line with a tight string or level.
If the door fails only in late afternoon, low sun is blinding the receiver, so shade it or swap the sides.
A receiver light that never comes on points to wiring or a failed sensor rather than alignment.
To prepare for sensor alignment, gather a few basic tools, clear the area around the sensors and cut power to the opener.
Unplug the opener and clean both lenses before you start.
Screwdriver or nut driver
String line or small level
Soft cloth for the lenses
Tape measure
Move bins, bikes and storage away from both sides of the door so you can reach the sensors and nothing blocks the beam. Note which sensor is the sender and which is the receiver, and check the sensor wires for staples or damage before you touch the brackets. If the door itself is heavy, crooked or has a broken spring, stop here and call a professional, since alignment will not fix it.
How to align garage door sensors comes down to setting both units at the same height and aiming them straight at each other until the receiver light stays steady. Here is the whole process at a glance, followed by each step in detail.
Unplug the opener.
Clean both sensor lenses.
Loosen the wing nut or screw on each bracket.
Point the sensors at each other at the same height, no more than 6 inches above the floor.
Use a tight string or level between them to check the line.
Tighten the brackets, plug in the opener and confirm both lights are steady.
Test by closing the door and passing an object through the beam.
One sensor sends the beam and the other receives it. The sender's light stays on; the receiver's light is steady only when it sees the beam.
So check the indicator lights closely: a dim, flickering or dark receiver light means the beam is missing or partly blocked.
These indicator lights are your guide throughout the sensor alignment process.
Check that both mounting brackets are tight against the wall or track and bent neither in nor out. Brackets often get knocked by bins, bikes or car bumpers.
A loose bracket lets the sensor drift.
Inspect the mounting brackets before any fine alignment. Look for bends, loose screws or a bracket that has been knocked loose from the track or wall. Straighten a lightly bent bracket or replace it if it will not hold its shape, then tighten the screws. A sensor cannot hold its aim on a bracket that moves.
Set the sensor height the same on both sides, a few inches above the floor and never more than 6 inches up. That sensor height lets them detect a small child or pet.
To set sensor height, measure from the floor to the center of each lens. Aim for about 6 inches and keep both sides equal so the beam runs level across the opening. On a sloped driveway or floor, the readings at each side may differ, so adjust until the lenses line up with each other rather than with the floor.
Horizontal alignment means aiming each sensor straight across the opening so the beam lands directly on the receiver lens.
Loosen the wing nuts and aim the sensors at each other, using a tight string or level between them, until the receiver light is steady.
Make small adjustments and wait a moment after each one, since some receiver lights take a second to settle. A second person watching the light makes this faster. Once the light is steady, tap the bracket gently. If the light flickers, the sensor is still marginal and needs a little more adjustment.
Tighten the brackets fully, then test the door to confirm the alignment holds and the safety reversal works.
Tighten the brackets, plug in the opener and close the door while passing an object through the beam. It should reverse.
Run the door through two or three full cycles. If it closes every time and reverses whenever the beam is broken, the job is done.
If sensor alignment does not hold, the cause is usually vibration, sunlight or wiring. The table lists the most common problems and what to try.
| Issue | Try |
|---|---|
| Light flickers | Tighten brackets; check for vibration |
| Works at night but not afternoons | Shade the receiver or swap sides |
| Light never comes on | Check wiring and connections |
In California, low afternoon sun in west-facing garages is a frequent cause of a door that fails only at certain times of day. A small sun shield over the receiver usually solves it.
Misaligned sensors usually come from small, repeated bumps. Trash bins, bikes and car bumpers knock the brackets, door vibration works the mounts loose over time, and wing nuts that were never fully tightened let the sensor drift. Tighten the bracket firmly after alignment, and add a small guard or a parking stop if the same sensor keeps getting hit.
Some sensor problems are not about alignment at all. Wiring, corrosion and failed parts can all look like misaligned sensors.
If alignment does not help, check for damaged wiring, corroded terminals or a failed sensor. A receiver that never lights may need replacing.
Coastal salt air can corrode terminals, and inland heat can crack wire insulation over time. If the opener flashes a fault code, our guide to garage door opener error codes can help narrow down the cause. Replace sensors as a matched pair made for your opener brand.
Preventative maintenance keeps sensors aligned and working with only a few minutes of attention each month.
Wipe the lenses monthly, keep the beam path clear and check the mounting brackets whenever something bumps them.
Test the reversal monthly by breaking the beam while the door closes.
Check the sensor lights after earthquakes or any bump to the brackets.
Keep storage and garden tools well clear of the sensors.
Fold sensor checks into your regular garage door maintenance.
Call a professional when alignment does not solve the problem, or when the door or wiring needs work beyond adjusting the brackets.
Call a technician if the lights never come on, the door fails the reversal test or wiring needs to be replaced inside walls.
Also call if the door is heavy, crooked or has a broken spring or cable. That hardware is under high tension and should only be handled by a technician. Some offer same-day service when a door will not close.
Here are quick answers to common questions about how to align garage door sensors.
The sender is usually the sensor whose light stays on whether or not the beam is blocked. The receiver's light glows steady only when it sees the beam, and it goes out or flickers when the beam is blocked. Light colors differ by brand, so check your opener's manual to confirm which sensor is which before you adjust them.
Yes, they can fail after years of sun, moisture or coastal salt air, which corrodes the terminals. Inland heat can also crack wire insulation over time. So if a receiver light never comes on after you have checked alignment and wiring, the sensor may need replacing. Replacement pairs are inexpensive; buy a matched pair made for your opener brand.
Your garage door sensors are aligned when both indicator lights are steady and the door closes fully every time. A flickering or dark receiver light means the beam is not reaching it. To confirm, close the door and pass an object through the beam. The door should stop and reverse right away. If it does, the sensors are aligned and working.
The sensor lights need power to guide you, so many people align them with the opener plugged in. Just keep your hands away from the door and do not run it while you work. Unplugging is safer while you loosen brackets or check wiring.
Leave your details and we'll get in touch.